详细化学反应机理对预混丙烷钝体熄火模拟影响

航空发动机熄火预测是重要关键问题之一，湍流和化学反应的非线性相互作用使预测非常困难。本文采用大涡模拟（LES）对湍流进行高精度模拟，采用概率密度函数输运方程湍流燃烧模型（TPDF）耦合JL4、Z66和H73三种化学反应机理，对预混丙烷钝体熄火现象和规律进行研究。JL4的反应机理最简单，反应释热快，局部放热高，火焰宽度大，火焰两侧温度梯度大，燃烧更加趋于稳定，无法模拟出熄火状态。H73机理绝热火焰温度低，火焰温度低，回流区中部OH含量高；在近熄火状态，大量CO被氧化，释放热量过高导致无法模拟出熄火现象。Z66机理可以模拟出火焰正常状态，在低当量比下也可以模拟出熄火状态。本文算例中，局部Da数大于1的区域超过35%则会发生熄火。     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

一种针对局部结构的有限元模型修正方法

针对实际结构有限元模型（FEM）的建模误差通常仅存在于局部区域，提出了一种对局部结构单独进行模型修正的方法。首先，根据频响函数（FRF）解耦理论得到由残余结构频响函数与包含待修正参数的局部结构动刚度所重构的整体结构频响函数的拟合值，然后通过迭代优化使其与测量值的残差最小化，从而得到参数的极大似然估计。在此基础上，将残差关于参数的灵敏度以局部结构动力学矩阵表示，建立了模型修正的基本方程，利用整体结构的测试数据即可直接对分离出来的局部结构进行模型修正。最后，对喷气式飞机和三角机翼飞机分别进行了数值模拟和实验研究，验证了所提方法的可行性和有效性。结果表明，所提方法可以成功地用于仅局部区域含有建模误差的实际结构有限元模型的修正，修正后的有限元模型的动态特性与实际结构有较好的一致性。     

相关函数在涡流检测信号提取分析中的应用

为降低涡流检测信号处理的硬件复杂程度及提升后续数据分析处理灵活度，在不借助复杂硬件自平衡技术电路前提下，在LABVIEW图形化软件平台中设计了相关函数算法程序，对示波器MDO4024C所采集的原始交流电桥信号及电桥激励信号分别进行自相关及互相关运算去噪，提取分析不锈钢管不同位置的涡流信号的幅值及相位，最后再将检测信号在极坐标图中分析显示。实验结果表明，这一方法可有效实现对不锈钢管缺陷涡流信号的去噪及特征信号提取。     

涡轮基组合循环发动机分布式控制系统通信网络混合拓扑结构优化方法

涡轮机组合循环(Turbine based combined cycle,TBCC)发动机控制系统通信网络拓扑结构是其分布式控制系统方案设计的重要部分,优化网络拓扑结构可提高发动机推重比和控制系统可靠性。本文基于智能优化算法提出TBCC分布式控制系统网络拓扑结构优化方法。基于图论建立TBCC几何模型和网格模型,以重量和可靠性为优化性能指标,同时考虑发动机表面高温区域以及控制节点的工作可靠性,分别采用粒子群算法和遗传算法优化星形结构中智能中央节点位置、中央节点的环形拓扑结构,获得星形-环形混合拓扑结构。仿真实例表明,基于本文方法优化所得的混合拓扑结构相较于星形集中式控制结构,系统重量降低了51.9%。     

An innovative approach for integrated airline network and aircraft family optimization

The determination of optimal aerial transport networks and their associated flight frequencies is crucial for the strategic planning of airlines, as well as for carrying out market research, to establish target markets, and for aircraft and crew rostering. In addition, optimum airplane types for the selected networks are crucial to improve revenue and to provide reduced operating costs. The present study proposes an innovative approach to determine the optimal aerial transport network simultaneously with the determination of the optimum fleet for that network, composed of three types of airplanes (network and vehicle integrated design). The network profit is maximized. The passenger’s demands between the airports are determined via a gravitational model. An embedded linear programming solution is responsible for obtaining potential optimal network configurations. The optimum fleet combination is determined from a database of candidate aircraft designs via genetic algorithm. A truly realistic airplane representation is made possible thanks to accurate surrogate models for engine and aerodynamics is adopted. An accurate engine deck encompassing a compression map and an innovative engine weight calculation besides an aerodynamical artificial neural network module enable a high degree of accuracy for the mission analysis. The proposed methodology is applied to obtain the optimum network comprised of twenty main Brazilian airports and corresponding fleet.     

独立函数的表达式及完备性

给出独立函数的逻辑表达式和递推关系式。证明了独立函数系的线性完备性。讨论逻辑函数关于独立函数系的展开式、不同极性独立函数系展式之间的关系,以及与Reed-Muller展式之间的关系。这些问题的结论为建立新型的通用逻辑模块奠定了理论基础。     

一种基于事件序列的故障树最小割集算法

在系统分析故障树最小割集各种求解算法的基础上，提出了一种故障树事件序列的数据结构，并针对该数据结构，设计了一种高效的故障树最小割集求解算法，并对其替换子算法、复制子算法和消减子算法进行了形式化描述。算法可有效降低最小割集生成中的“组合爆炸”问题，实验结果表明算法具有较好的计算性能。     

平面形状误差分离方法的比较分析

就十种典型的精密平面形状误差测量－分离方法的权函数及其零点，作了分析比较。按形状误差谐波抑制最小准则，论证了五点式正交逐次三点法、九点式正交逐次三点法、复合三点法、不对称二维混合法和不对称四点法优于其他方法，不对称四点法则较为理想。     

含有任意多个椭圆孔弹性板的应力场计算

本文应用弹性力学的复变函数理论,用多保角变换的方法,导出了含有任意多个椭圆孔的无限大弹性板多复变量应力函数的表达式。每个孔的大小、位置和孔边作用的载荷均为任意指定。板的无限远处作用有和坐标轴方向一致的均匀拉压载荷P_x,P_y和均匀剪切载荷P_(xy)。并在孔边进行复Fourier级数展开,用待定系数法确定应力函数的未知系数,从而计算弹性板的应力场。编制了相应的FORTRAN77标准化程序,进行了考题和算例分析,给出了级数的收敛状况和孔边周向应力的分布图。